Push Pull Connection Kits
There are a few places that need connections:
1) Cable to control head(s),
2) Cable to engine or clutch,
3) and possibly a mounting kit to hold down the cable to the engine and/or the clutch.
You can see a diagram of typical installations here.
Control head connection kits
 |
These kits are designed for attaching a push-pull cable to the control head.
Since cables are either 33 series or 43 series, you need to have the kit that
matches the control head and the cable series being used.
That's why kits are not just included with the control heads.
To order a connection kit, order either:
-0901 (for 33 series cables) or
-0902 (for 43 series cables) or
-0912 (for 60 series cables; not available for all models).
The part number looks like this:
20xx-0901 where xx is the control head. e.g. 2009-0901 for a 2009 control head.
You need one kit for every cable connected to a control head.
If you are running cables in "series" (see connection diagrams),
you will need more control head connection kits because the cable runs from control head to control head.
For example, a 2 station, single engine system would use 4 connection kits for a parallel installation, but
a series installation would need 6 kits.
2091 to 2094 control heads include connection kits for the 47 series "interconnecting" cable.
You still need to get the -0901 or -0902 kits for the primary control head.
Connection kits are not always interchangeable.
If you happen to have a kit for one control head, it probably will not work on a different
model. Click here for a list of interchangeable connection kits.
|
Neutral Safety Switch Kits
We recommend that you order the Neutral Safety Switch Kit pre-installed when you order the control head.
If you need one afterwards, please state the control head number followed by -0903.
e.g. 2009-0903
Click here to see which controls have 0903 kits.
Electric Clutch Control Bracket
The Electric Clutch Control Bracket (model 2170) can be installed on most Push Pull heads for the purpose
of controllng an electrically actuated clutch.
We recommend that you order it pre-installed when you order the control head.
If you need one afterwards, please state the control head number followed by -0910.
e.g. 2009-0910
Click here to see which controls have 0910 kits.
Throttle Extension Kits
The throttle extension kits will add upto 1" of extra stroke for the throttle on Models
2046, 2048, 2081, 2083, 2085, 2091 to 2094.
Please state the control head number followed by the numbers:
| -0905 | 30 Series Throttle (including Connection Kit) |
| -0906 | 40 Series Throttle (including Connection Kit) |
| -0907 | 30 Series Override/Trolling Kit (including Connection Kit) |
| -0908 | 40 Series Override/Trolling Kit (including Connection Kit) |
Rod Ball Ends
Rod Ball Ends are commonly used to connect a push-pull cable to the engine or clutch.
The rod ball end is screwed onto the end of the cable,
and the rod ball end uses a bolt through the ball end that attaches it to a lever.
 |
We have rod ball end of various sizes:
| Part# | Thread size | Bolt Hole |
|---|
| 2143 | 3/16" UNF | 3/16" |
| 2143/4 | 3/16" UNF | 1/4" |
| 2144 | 1/4" UNF | 1/4" |
| 2144/3 | 1/4" UNF | 3/16" |
| 2145 | 5/16" UNF | 5/16" |
| 2146 | 3/8" UNF | 5/16" |
| 2148 | 1/2" UNF | 5/8" |
| 2149 | 5/8" UNF | 3/4" |
|
Cable Clamp Kits
These are used to mount the end of the cable to flat surface near the engine or clutch.
 | 2131-0030 Holds one 33 series cables. |
 | 2131-0040 Holds one 40 series cables. |
 | 2142-0030 Holds two 33 series cables. |
 | 2142-0040 Holds two 40 series cables. |
We also have a 2131-0060 for holding one 60 series cable.
Levers
Levers are used to connect a rod ball end, or ball-joint to another mechanical connection.
This is useful for changing the stroke required, or turning a shaft.
2104 Levers
-0001 -0002 -0003
-0004 -0005 -0006
-0007 -0008 |
The part numbers are shown below the levers.
e.g. 2104-0001 is the leftmost. |
Specifications
| Part# | Length | Holes | Hole size | Bore sizes
for shaft |
2104-0001 | 5" | 6 | 1/4" | 1/2", 5/8", 3/4" |
2104-0002 | 3 1/2" | 4 | 1/4" | 1/2", 5/8" |
2104-0003 | 3" | 5 | 3/16" | 5/8" |
2104-0004 | 4 1/4" | 6 | 3/16" | 1/2" |
2104-0005 | 4 1/4" | 6 | 3/16" | 5/8" |
2104-0006 | 4 1/4" | 6 | 1/4" | 5/8" |
2104-0007 | 3" | slotted | 1/4" | 5/8" |
2104-0008 | 4 3/8" | slotted | 1/4" | 5/8" |
Please specify the bore size you would like.
You can tell us the size or add the following letter code to complete the part number. e.g. 2104-0001-A
Add "-A" for 1/2"
Add "-B" for 5/8"
Add "-C" for 3/4"
Universal Catch-A-Bolt
This is a universal adaptor kit which replaces all specialty adapter kits.
 | Part# 2128
This adaptor kit can be used to take either 30 or 40 series cables,
and either single or double cables (similar to the 2131 and 2142 adaptors).
Order the 2128 and the connector you need:
| Part# | Description |
|---|
| 2128-0031 | 30 series - Single cable clamp |
| 2128-0032 | 30 series - Double cable clamp |
| 2128-0041 | 40 series - Single cable clamp |
| 2128-0042 | 40 series - Double cable clamp |
|
Other Adaptors
2123 Universal Cable Transfer unit can alter the direction of cable (pull to push), or change the cable stroke.
2124 Compound unit can tie cables together or multiple engines (for one handle).
Click here to get details on connecting Push - Pull control heads.
Go to the Push Pull page.
Return Back
|
